全自动上料搅拌车使用前应该做到哪些？_公司新闻_新闻资讯_全自动上料搅拌机车

新闻资讯

行业新闻公司新闻

热点推荐

自动上料搅拌机配件是由哪两部分组成的？

2022-12-23

修路有哪些不错的机械设备？先说说这个小型搅拌车

2022-12-19

自上料搅拌车操作须知的五项重要内容

2022-12-16

自上料拌和车的特征有哪些？

2022-12-12

自动上料搅拌车能解决哪些施工难题？

2022-12-02

混凝土搅拌车的刹车片要怎样挑选合格

2022-11-14

关于山汽

联系人：刘老师

电话：400-879-1999

公司：山东山汽工程机械（集团）有限公司

地址：山东省莱州市206国道与308省道交叉口东南50米

全自动上料搅拌车使用前应该做到哪些？

所属分类：公司新闻发布时间：2021-06-15 来源：http://www.shanqijituan.com 浏览量：0

1、检查各个水箱是否缺水并加足水，轮胎气压是否符合2.5bar以_上要求。

1. Check whether each water tank is short of water and full of water, and whether the tire pressure meets the requirement of 2.5bar_ I'm not sure.

2、检查发动机机油油尺，液压油箱标尺，齿轮箱油标观察孔，前、后桥，轮边减速轴头拧开油面油堵检查齿轮油是否符合要求，缺少应及时添加，总泵自动液油杯液面是否合乎标准要求。

2. Check the engine oil dipstick, hydraulic oil tank ruler, gearbox oil level observation hole, front and rear axle, wheel side reducer shaft head, screw off the oil level oil plug, check whether the gear oil meets the requirements, if it is missing, add it in time, and whether the automatic oil cup level of master cylinder meets the standard requirements.

3、观测发动机机油，齿轮油，检查油标尺，油标锣孔，液压油箱时，车辆要水平位置。

3. Observe the engine oil, gear oil, check the oil dipstick, oil mark, Gong hole, hydraulic oil tank, the vehicle should be in a horizontal position.

4、全车各部油管路，气管路接头是松动有无漏油，漏气现象。检查全车线路有无接触不良，各仪表，灯光是否工作正常。

4. The oil pipes and gas pipe joints of all parts of the car are loose, whether there is oil leakage or air leakage. Check if there is poor contact in the whole vehicle line, and if all instruments and lights work normally.
全自动上料搅拌车

5、行驶前刹车是否制动有效，检查各操纵阀作用是否良好。

5. Check whether the brake is effective before driving, and check whether each control valve works well.

各操作阀的作用

Function of each operating valve

1、主车前后行走操纵阀( 快慢档，前进和倒车档)-般行走时为前驾，施工作业时为后驾。

1. The front and rear travel control valve (fast and slow, forward and reverse gears) of the main vehicle is generally the front drive when walking, and the rear drive when working.

2、大臂升降旋转操纵阀，举料，左右旋转罐体控制。

2. Boom lifting rotary control valve, lifting, left and right rotary can body control.

3、料斗上下料操纵阀，铲料、卸料控制铲斗作用。

3. Hopper loading and unloading control valve, shovel, discharge control bucket function.

图片

picture

4、手动油门操纵阀，控制发动机的转速，使搅罐在一定的平稳速度下旋转。

4. The manual throttle control valve controls the speed of the engine to make the stirring tank rotate at a certain steady speed.

5、座椅脚踏定位卡销，用于座椅调转方向时起到锁止作用，踏板踩向下时。锁销打开，左翼转到位置后制动锁止。

5. The foot positioning pin of the seat is used to lock the seat when the seat rotates, and when the pedal is depressed. When the lock pin is opened and the left wing is turned to the position, the brake is locked.

做好日常保养，每次施工结束，必须清洗干净车辆外表面和罐体内残余科，以防混凝土凝聚在罐体内外。

Do a good job in daily maintenance. At the end of each construction, the external surface of the vehicle and the residual parts in the tank must be cleaned to prevent the concrete from condensing inside and outside the tank.

加强对发动机，齿轮箱，车桥周期性保养，长时间停用，水箱内不宜储水。1200小时更换机油和齿轮油，连续工作7天清洗柴油，机油滤芯，空气滤芯100小时清洗一次。

Strengthen the engine, gearbox, axle periodic maintenance, long time out of service, water tank should not be stored. Change engine oil and gear oil for 1200 hours, clean diesel oil, engine oil filter element and air filter element for 7 consecutive days, and clean once every 100 hours.

上一页：全自动上料搅拌车车身油箱体积变小与什么有关？下一页：4方全自动上料搅拌车过程中容易出现的问题